Benjamin Moore Industrial Specialty Paint Products for removing rust

Try our new mobile phone site www.TexasPaint.mobi

Home

Shopping

Products

Specials

Company

Locations

FAQ's

Site Map

Bulletin Board

These products are not sold online.

To purchase these products by phone - Contact Us

Sweep-Up Spray Alkyd Flat M51
MSDS	Technical Data Sheet
Product Information This fast dry product is designed to provide superior hiding for one coat work. Retains its whiteness in presence of industrial fumes. The dry fall qualities of this product cause the overspray to settle as a dry powder in approximately 10 feet of fall depending on air movement, temperature, & humidity. Greatly reduces clean up costs. May be applied on virtually any interior wall or ceiling. Requires minimal surface preparation. Clean up tools immediately after use with VM&P naphtha or Xylol. Recommended Uses Protects Interior industrial ceilings or walls. Performs well where a high hiding less expensive coating is needed. For production or work areas where wet overspray could not be tolerated and industrial areas exposed to welding or production dust. Colors: M51-01 White

Sweep-Up Spray Alkyd Eggshell M52
MSDS	Technical Data Sheet
Product Information This fast dry product is designed to provide superior hiding for one coat work. Retains its whiteness in presence of industrial fumes. The dry fall qualities of this product cause the overspray to settle as a dry powder in approximately 10 feet of fall depending on air movement, temperature, and humidity. Greatly reduces clean up costs. May be applied on virtually any interior wall or ceiling. Requires minimal surface preparation. Clean up tools immediately after use with VM&P naphtha or Xylol. Recommended Uses Protects interior industrial ceilings or walls. Performs well where a high hiding, less expensive coating is needed. For use over production or work areas where wet overspray could not be tolerated or areas exposed to welding or production dust. Colors: White

Sweep-Up Spray Latex Flat M53
MSDS	Technical Data Sheet
Product Information This fast dry product is designed to provide superior hiding for one coat work. Retains its whiteness in presence of industrial fumes. The dry fall qualities of this product cause the overspray to settle as a dry powder in approximately 10 feet of fall depending on air movement, temperature, and humidity. Greatly reduces clean up costs. May be applied on virtually any interior wall or ceiling. Requires minimal surface preparation. Clean up tools immediately after use with clean water. Recommended Uses Protects interior industrial ceilings or walls. Performs well where a high hiding, less expensive coating is needed. For use over production or work areas where wet overspray could not be tolerated or areas exposed to welding or production dust. Colors: M53-01 White

Safety & Zone Marking Alkyd M56
MSDS	Technical Data Sheet
Product Information This fast dry alkyd coating is designed for marking traffic lanes on streets, highways, parking lots, airports, warehouses, shopping centers. For designating parking spaces and other vehicular or foot traffic control markings, traffic beads may be utilized with this coating to provide reflective marking, If beads are to be used they should be dropped into the wet paint immediately after application at a rate of 6 pounds per gallon of paint. This coating may be applied to concrete or asphalt surfaces interior or exterior. Recommended Uses Coating asphalt or concrete surfaces, interior or exterior, traffic lanes, streets & highways, parking lots, parking spaces, crosswalks, fire lanes, vehicular and floor traffic control markings, "No Parking" areas, airports, manufacturing plants, shopping centers, schools, hospitals, warehouses. Not for use as an anti-slip coating on invalid ramps or sidewalks without the addition of an anti-slip aggregate,. Do not apply to extremely hot surfaces or when the surface and air temperatures are below 50 F. Allow newly applied asphalt seal coats to dry at least 4 days before application. Colors: M56-01 White M56-10 Yellow

Technical Data	White
Generic Type	Modified Alkyd
Pigment Type	Titanium Dioxide and Calcium Carbonate
Volume Solids	55%
Spread Rate per Gal.	3" line: 440 feet
Film Thickness - Wet - Dry	14.5 mils 8.0 mils
Dry Time - To Touch - Recoat	15 Minutes
Dry Heat Resistance	200° F
Viscosity	80 ± 5 KU
Flash Point (Seta)	None
60° Specular Gloss	10-20%
Clean Up With	VM&P Naphtha
Mixing Ratio	N/A
Induction Time	N/A
Pot Life @ 70° F	N/A

Safety & Zone Marking Latex M58
MSDS	Technical Data Sheet
Product Information This fast dry latex coating is designed for marking traffic lanes on streets, highways, parking lots, airports, warehouses, shopping centers. For designating parking spaces and other vehicular or foot traffic control markings. Traffic beads may be utilized with this coating to provide reflective marking, If beads are to be used they should be dropped into the wet paint immediately after application at a rate of 6 pounds per gallon of paint. This coating may be applied to concrete or asphalt surfaces interior or exterior. Recommended Uses Coating asphalt or concrete surfaces, interior or exterior, traffic lanes, streets & highways, parking lots, parking spaces, crosswalks, fire lanes, vehicular and floor traffic control markings, "No Parking" areas, airports, manufacturing plants, shopping centers, schools, hospitals, warehouses. Not for use as an anti-slip coating on invalid ramps or sidewalks without the addition of an anti-slip aggregate,. Do not apply to extremely hot surfaces or when the surface and air temperatures are below 50° F. Allow newly applied asphalt seal coats to dry at least 4 days before application. Colors: M58-01 White M58-10 Yellow M58-20 Red M58-30 Blue M58-80 Black

Please read our Website Policies Page. Product selection, pricing and availability is subject to change without notice.

Website designed by Texas Paint & Wallpaper Co. / Shopping cart powered by FastCatCarts.com