|
Acrylic
Metal Primer M04
|
|
MSDS |
Technical
Data Sheet |
Product
Information
This unique water-thinned, acrylic primer
eliminates flash rusting; plus protects the
steel from corrosion. Because it is water
thinned, it has less odor and reduces the
risk of fire hazard. This product eliminates
the need for expensive solvents, and also
performs well as a tie coat or barrier coat
over zinc coated surfaces. This primer can
be applied to damp surfaces, and adheres
well to most hard-to-coat substrates. It can
also be applied to poured or cast concrete
and brick.
Recommended
Uses:
For use in food processing plants, bottling
plants, water filtration plants, waste water
treatment plants, or for general maintenance
painting.
Colors:
M04-01 White
Tint Bases:
Not Available
|
|
| Technical
Data |
White |
| Generic
Type |
Acrylic
Latex |
| Pigment
Type |
Titanium
Dioxide/
Corrosion
Inhibitors |
| Volume
Solids |
40% |
| Spread
Rate per Gal. |
320
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
5.0
mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
30
Minutes
2 hours |
| Dry
Heat Resistance |
160°
F |
| Viscosity |
85
± 5 KU |
| Flash
Point (Seta) |
None |
| 60°
Specular Gloss |
Matte |
| Clean
Up With |
Clean
Water |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70° F |
N/A |
|
| |
|
|
Rapid
Dry Metal Primer CM05 |
|
MSDS |
Technical
Data Sheet |
Product
Information
This quick dry rust inhibitive primer
permits faster handling for in-shop or field
application. Corrosion inhibitive pigments
provide protection during fabrication,
storage, construction or erection phases.
Excellent adhesion promotes long term
durability.
Recommended Uses
Clean dry structural steel, equipment,
catwalks, railings, storage tanks,
implements and for general maintenance
painting. Performs well where fast dry
coatings are needed.
Not for
immersion service or on previously coated
surfaces that could be affected by strong
solvents. Top coating with a strong solvent
should be performed within 3 hours or after
30 hours.
Colors: Gray
|
|
| Technical
Data |
|
| Generic
Type |
Modified
Alkyd |
| Pigment
Type |
Rust
Inhibitor and Select Inerts |
| Volume
Solids |
42%
(50%) |
| Spread
Rate per Gal. |
455
Sq. Ft.
(400 Sq. Ft.) |
Film
Thickness
- Wet
- Dry |
3.5
(4.0) mils
1.5 (2.0) mils |
Dry
Time
- To Touch
- Recoat |
15
min.
1-2 hours (see caution) |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
85+/-
5 KU
(80+/- 5 KU) |
| Flash
Point (Seta) |
83°
F
(74° F) |
| 60°
Specular Gloss |
0-5% |
| Clean
Up With |
M94 |
| Mixing
Ratio |
N/A |
|
| |
|
|
Alkyd
Metal Primer CM06 |
|
MSDS |
Technical
Data Sheet |
Product
Information
This modified alkyd primer permits same day
finish coat application. Provides excellent
long term corrosion control with outstanding
adhesion properties. The ability to
penetrate provides good performance over
hand or power tool cleaned surfaces.
Recommended
Uses
For priming structural steel, storage tanks,
equipment, machinery, conveyers, metal
buildings, barges, fences and for general
maintenance painting on interior or exterior
surfaces.
Colors:
M06-20 Red, M06-70 Gray
Tint Bases:
Not Available
|
|
| Technical
Data |
Red |
| Generic
Type |
Alkyd |
| Pigment
Type |
Corrosion
Inhibitors/
Select Inerts |
| Volume
Solids |
47% |
| Spread
Rate per Gal. |
380
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
4.2
mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
1
Hour
3-4 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
85
± 5 KU |
| Flash
Point (Seta) |
107°
F |
| 60°
Specular Gloss |
0-5% |
| Clean
Up With |
Mineral
Spirits |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70° F |
N/A |
|
| |
|
|
Universal
Metal Primer M07 |
| MSDS |
Technical
Data Sheet |
Product
Information
This quick dry universal primer is
formulated for use under many generic type
finish coats. It offers excellent rust
inhibition and good adhesion, both of which
contribute to extended coating life. This
coating serves as a barrier coat which will
keep hot solvent coatings from attacking
conventional coatings. This primer performs
well when priming is essential before the
generic type of finish coat has been chosen.
Recommended
Uses
Performs well on structural steel,
equipment, tanks, implements, catwalks,
stairs, railing, conveyers, for shop or
field painting, and for general maintenance
painting on interior or exterior surfaces.
Colors:
M07-20 Red, M06-70 Gray
Tint Bases:
Not Available |
|
| Technical
Data |
Red |
| Generic
Type |
Phenolic
Alkyd |
| Pigment
Type |
Corrosion
Inhibitors |
| Volume
Solids |
52% |
| Spread
Rate per Gal. |
420
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
3.8
mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
15
Minutes
1-2 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
75
KU |
| Flash
Point (Seta) |
83°
F |
| 60°
Specular Gloss |
0-5% |
| Clean
Up With |
Xylene |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70° F |
N/A |
|
| |
|
|
Waterborne
Epoxy Primer M08/M09 |
|
MSDS |
Technical
Data Sheet |
Product
Information
This two component rust inhibitive primer
provides an excellent chemical resistant
base for high performance top coat systems.
This water thinned formula is low odor
making it a desirable primer for use in food
processing or for application in areas where
odor could be offensive.
Recommended
Uses
For use in food processing plants, chemical
plants, pulp and paper mills, water or waste
treatment plants, pharmaceutical plants,
refineries, marine or offshore structures
Colors:
M08-70 Gray
Tint Bases:
Not Available
|
|
| Technical
Data |
Gray |
| Generic
Type |
Waterborne
Acrylic Epoxy |
| Pigment
Type |
Corrosion
Inhibitors/
Titanium Dioxide |
| Volume
Solids |
38%
Mixed |
| Spread
Rate per Gal. |
300
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
5.3
mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
2
Hours
4 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity
(Mixed) |
75±
5 KU |
| Flash
Point (Seta) |
None |
| 60°
Specular Gloss |
Matte |
| Clean
Up With |
Clean
Water |
| Mixing
Ratio |
4:1 |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
12
hours |
|
| |
|
|
Shop-Cote
Metal Primer M12 |
| MSDS |
Technical
Data Sheet |
Product
Information
Designed for use in shop priming fabricated
steel to be used in mild or moderate
atmospheric exposure. This fast dry primer
provides good wetting properties necessary
for bonding to hand and power tool cleaned
surfaces. This premium shop coat will
provide weather protection without being top
coated for extended periods under normal
conditions.
Recommended
Uses
For use in steel fabrication shops and for
priming support steel. Protects steel
exposed to moderate environments.
Colors:
M12-20 Red, M12-70 Gray
Tint Bases:
Not Available
|
|
| Technical
Data |
Red |
| Generic
Type |
Modified
Alkyd |
| Pigment
Type |
Red
Oxide/
Zinc Phosphate |
| Volume
Solids |
44% |
| Spread
Rate per Gal. |
350
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
4.5
mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
20
Minutes
4-6 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
75±
5 KU |
| Flash
Point (Seta) |
100°
F |
| 60°
Specular Gloss |
Flat |
| Clean
Up With |
Mineral
Spirits |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70° F |
N/A |
|
| |
|
|
Epoxy
Zinc Rich Primer CM18/19 |
|
MSDS |
Technical
Data Sheet |
Product
Information
This two component epoxy zinc rich primer
provides optimal galvanic protection for
steel surfaces exposed to corrosive
environments. This effective action is
derived from the galvanic couplers formed
between the zinc in the coating and the
metal substrate. This protection exists even
if the primer is scratched or gouged. This
primer provides the chemical resistance
needed to support the high performance top
coats.
Recommended Uses
Corrosive Industrial Environments, Marine or
Offshore Structures, High Humidity or
Coastal Areas, Cooling Towers, Chemical
Plants, Water or Waste Treatment Plants,
Fertilizer Plants
Colors: Zinc
Gray
|
|
| Technical
Data |
|
| Generic
Type |
Polyamide
Epoxy |
| Pigment
Type |
Metalic
Zinc Dust |
| Volume
Solids |
47%
mixed
(55%) |
| Spread
Rate per Gal. |
300
Sq. Ft.
(350 Sq. Ft.) |
Film
Thickness
- Wet
- Dry |
5.3
(4.5) mils
2.5 mils |
Dry
Time
- To Touch
- Recoat |
4
hours (1 hour)
16 hours (8 hours) |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
80+/-5
KU
(85+/-5 KU) |
| Flash
Point (Seta) |
82°
F
(84° F) |
| 60°
Specular Gloss |
0-5% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
|
| |
|
| Polyamide
Epoxy Metal Primer CM33/M34 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two-component polyamide epoxy primer is
designed to protect properly prepared steel
surfaces when exposed to corrosive
environments. It provides excellent rust
inhibition and chemical resistance for
interior or exterior surfaces, and offers
the adhesion necessary for application of a
variety of high performance top coats.
Recommended
Uses
Protecting steel storage tanks, structural
& support steel, equipment, machinery,
metal buildings, on both interior or
exterior surfaces. Protects surfaces in pulp
& paper mills, waste treatment plants,
food processing areas, water filtration
plants, marine or offshore rigs, rolling
stock, fertilizer plants, chemical
processing and bottling plants.
Colors:
M33-20 Red, M33-70 Gray (Mixed with M3484
Catalyst)
Tint Bases:
None |
|
| Technical
Data |
|
| Generic
Type |
Polyamide
Epoxy |
| Pigment
Type |
Titanium
Dioxide
and Select Inerts |
| Volume
Solids |
48%
Mixed |
| Spread
Rate per Gal. |
385
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
4.2
mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
11/2
hours
4 hours |
| Dry
Heat Resistance |
300°
F |
| Viscosity
(mixed) |
80
± 5 KU |
| Flash
Point (Seta) |
80°
F |
| 60°
Specular Gloss |
0-6% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
1:1
by volume |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
8
hours |
|
| |
|
| Rust
Converter Coating M82 |
| MSDS |
Technical
Data Sheet |
Product
Information
This water thinned coating is a film forming
material that chemically converts rust into
a black inert non-corrosive iron complex.
This coating provides two step protection in
one application. First, it converts tightly
adherent rust into a non-rusting black film.
Second, it provides corrosion protection
against new rust forming.
Recommended
Uses
Equipment, structural steel, lawn furniture,
decorative gates, posts and railings,
machinery, Surfaces not accessible for blast
cleaning
Colors:
M82-00
|
|
| Technical
Data |
|
| Generic
Type |
Modified
Latex |
| Pigment
Type |
Inert |
| Volume
Solids |
51% |
| Spread
Rate per Gal. |
400
Sq. Ft.
|
Film
Thickness
- Wet
- Dry |
4.0
mils
2.0 mils |
Dry
Time
- To Touch
- To Handle
- To Recoat |
15
Minutes
2 hours
3 hours |
| Dry
Heat Resistance |
200°
F |
| Viscosity |
65
± 5 KU |
| Flash
Point (Seta) |
>250°
F |
| 60°
Specular Gloss |
10% |
Clean
Up With
Clean Up Clean Up With |
Do
Not Thin
Clean Water |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70° F |
N/A |
|
| |
|
| Oil
& Grease Emulsifier M83 |
| MSDS |
Technical
Data Sheet |
Product
Information
This cleaner is designed to convert oil,
grease, fats, blood and animal by-products
into a soapy solution which floats up and
out of a surface during the rinsing process.
It effectively removes wax off of tile or
inlayed floors. Cleans tools and equipment.
This emulsifying process permeates into
voids, cracks, or concrete surfaces
converting the oily matter into a soapy
solution permitting easy removal.
Recommended
Uses
Concrete, wood, or metal floors
Cleaning machinery, tanks, and equipment
Removing oily films from cleanable,
paintable surfaces
Keep from
freezing
|
|
| Technical
Data |
|
| Spread
Rate per Gal. |
100
Sq. Ft.
|
| Clean
Up With & Neutralizer |
Clean
Water |
| Mixing
Ratio |
heavy
soil:1 to 6
light soil: 1 to 15 |
| Working
Time |
15-20
min |
|
| |
|
| Rust
Pretreatment M84 |
| MSDS |
Technical
Data Sheet |
Product
Information
This product is designed to penetrate rusted
areas converting the iron oxide into iron
phosphate which is chemically inert. This
hard black substance increases the coating
adhesion. it makes it difficult for water
and air to permeate thru the coating and
attack the metal. After the treated surface
has dried, remove any gray powdery residue
by wiping, using clean rags and solvent.
Treated surfaces should receive proper
coating system within 48 hours after
treating.
Recommended
Uses
Converting rust that can not feasibly be
removed by other methods, supplements other
cleaning methods, tanks, railings, catwalk
gratings, machinery, and equipment
Keep from
freezing.
Not for
immersion service.
|
|
| Technical
Data |
|
| Reduction |
3:1
water to M84 |
| Spread
Rate per gallon |
Light
Rust: 400 Sq. Ft.
Average Rust:
300 Sq. Ft.
|
| Neutralizer |
Clean
Water |
| Working
Time |
Light
Rust: Allow to Dry
Average Rust:
Overnight Dry
|
| Cleanup |
Remove
gray powdery residue with M94 or Xylol |
| Caution |
Contains
Phosphoric Acid |
|
| |
|
| Concrete
Pretreatment & Etch M85 |
| MSDS |
Technical
Data Sheet |
Product
Information
This pretreatment is designed to penetrate
and remove concrete laitance and other
foreign matter. The process neutralizes lime
and alkali, and opens up the concrete
surface so the coating can penetrate. This
product contains inhibitors which keep the
acid from attacking equipment and drains. It
also contains extenders which provide a more
even etch of larger areas. The floor should
be dampened before applying the M85 and all
steps should be taken to ensure the floor
remains damp during the cleaning process.
Recommended
Uses
Etching and pre-treating concrete surfaces
prior to painting, poured concrete walls,
floors, and pre-cast panels
Apply only to
fully cured concrete. Dampen floor before
applying M85. Keep all concrete surfaces
damp during the cleaning process. Read
safety information section for proper
handling of this acid. Caution: Always add
acid to water. Never reduce acid by adding
water to acid.
|
|
| Technical
Data |
|
| Clean
Up With |
Water |
| Reduction |
3:1
water to M85 |
| Spread
Rate per gallon |
100
Sq. Ft. |
| Neutralizer |
Add
5% M85 to 95% water for rinsing to remove
oily deposits and set proper pH. |
| Recoat
Time |
Overnight |
| Caution |
Always
add acid to water. |
|
