| |
|
Waterborne
Epoxy Block Filler M31/32
|
|
MSDS |
Technical
Data Sheet |
Product
Information
This two component epoxy block filler will provide
the required filling properties on coarse masonry
or concrete block. it will also provide the
bonding properties needed to support any two
component product when used on high abuse
surfaces, high moisture areas or below grade
applications. May be top coated with most generic
coatings and cleans up with soap and water. This
product has a useable pot life of 6 to 8 hours at
70° F
Recommended Uses
Coarse open masonry, concrete block or brick
walls. Can be used in food processing plants,
bottling plants, water & waste treatment
plants, pulp & paper mills, fertilizer plants
dairies, power plants, auto washing facilities,
and sugar mills. For both interior and exterior
applications.
- Not for floors
- Not for immersion
- Do not expose to low temperature curing
conditions.
- Exhibits a tendency to yellow and chalk when
exposed to UV light.
Colors: White
|
|
| Technical
Data |
White |
| Generic
Type |
Waterborne
Epoxy |
| Pigment
Type |
Organic
Fibers and Inerts |
| Volume
Solids |
46%
mixed
|
| Spread
Rate per Gal. |
75
Sq. Ft.
|
Film
Thickness
- Wet
- Dry |
22
mils
10 mils |
Dry
Time
- To Touch
- Recoat |
2
hours
16 hours |
| Dry
Heat Resistance |
160°
F |
| Viscosity |
Mastic |
| Flash
Point (Seta) |
none |
| 60°
Specular Gloss |
Flat |
| Clean
Up With |
Clean
Water |
| Mixing
Ratio |
1:1 |
| Induction
Time |
30
min |
| Pot
Life @ 70° F |
8
hours |
|
| |
|
| Polyamide
Epoxy Gloss Coating M36/M37,
CM36/37 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two-component epoxy offers excellent impact
and abrasion resistance plus outstanding solvent,
alkali, and acid resistance. It resists strong
cleaning solutions and provides a tough waterproof
film that forms an effective barrier coat with
superior resistance to salt and fresh water. The
catalyzed coating bonds itself to the substrate
and yet remains flexible. When used as a tinting
base using Benjamin Moore's Industrial Maintenance
Coatings Industrial Tinting System colorants,
Tintable White can be used to create hundreds of
light and pastel shades. Also available in tint
bases for virtually unlimited color selection.
Recommended
Uses
Colors: M36-90
Tintable White, M36-91 Deep Base, M36-92 Clear
Base, (all mixed w/M37 catalyst) |
|
| Technical
Data |
Tintable
White |
| Generic
Type |
Polyamide
Epoxy |
| Pigment
Type |
Titanium
Dioxide
and Select Inerts |
| Volume
Solids |
55% Mixed
(61%)
|
| Spread
Rate per Gal. |
440
Sq.Ft.
(485 Sq.Ft.) |
Film
Thickness
- Wet
- Dry |
3.6
(3.3) mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
1-11/2
hours
8 (16) hours |
| Dry
Heat Resistance |
300°F |
| Viscosity
(mixed) |
70
± 5 KU |
| Flash
Point (Seta) |
81°F |
| 60°
Specular Gloss |
80-90% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
1:1
by volume |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
6-8
hours |
|
| |
|
| Polyamide
Epoxy Semi-Gloss Coating M36/M38 |
| MSDS |
Technical
Data Sheet |
|
Product
Information
This two component semi-gloss epoxy offers very
good acid and chemical resistance, plus very good
impact and abrasion resistance. Withstands strong
cleaning compounds and does not support mold,
mildew and fungi growth. Very good hiding and
leveling. Produces a tile-like finish for easy
maintenance. May be used for coating interior or
exterior surfaces.
Recommended
Uses
Protects
metal, masonry, wood, plaster or drywall on
interior or exterior surfaces. Performs well on
walls, partitions, lockers, equipment, storage
tanks, ceramic tile walls. For food processing
plants, breweries, dairies, bottling plants,
schools, hospitals, nursing homes.
Limitations:
•
Gloss reduction on exterior surfaces • Slight
ambering in the presence of U.V. light and ammonia
compounds • When used as a floor coating, apply
at a rate of 150 sq.ft./gal. and consider the need
for an anti-slip aggregate. • Does not cure
below 55° F
Colors: |
|
| Technical
Data |
Tintable
White |
| Generic
Type |
Polyamide
Epoxy |
| Pigment
Type |
Titanium
Dioxide
and Select Inerts |
| Volume
Solids |
60%
Mixed |
| Spread
Rate per Gal. |
380
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
4.2
mils
2.5 mils |
Dry
Time
- To Touch
- Recoat |
1
hour
16 hours |
| Dry
Heat Resistance |
300°
F |
| Viscosity
(mixed) |
90
± 5 KU |
| Flash
Point (Seta) |
83°
F |
| 60°
Specular Gloss |
40% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
1:1
by volume |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
8
hours |
|
| |
|
| Polyamide
Epoxy Hi-Build Gloss Coating M36/M39 |
| MSDS |
Technical
Data Sheet |
|
Product
Information
This two component high build epoxy offers very
good impact and abrasion resistance from heavy
foot traffic. Resists acid, chemicals and strong
cleaning compounds. Does not support mold, mildew
or fungi growth. This non-toxic coating has
superior resistance to salt and fresh water. The
high solids of this coating permit good leveling
and filling of old, abused floor areas. Available
in Clear as well as a variety of colors.
Recommended
Uses
Use
on properly prepared surfaces exposed to high
abuse. For use in refurbishing abused concrete
floors. Forms a tough, dense, waterproof film on
floors and walls. Provides an effective insulating
barrier for corrosion control. For water and waste
treatment plants, food processing plants, dairies,
chemical plants, pulp and paper mills, bottling
plants, pharmaceutical plants, bakeries, power
generating plants, storage tanks, equipment,
machinery, catwalks, railings, and stairs.
Limitations:
•
Gloss reduction and tendency to yellow on exterior
surfaces • Slight ambering in the presence of
strong U.V. light and ammonia compounds • When
used as a floor coating, apply at a rate of 150
sq.ft./gal. and consider the need for an anti-slip
aggregate. • Does not cure below 55° F
Colors:M36-90
Tintable White, M36-91 Deep Base, M36-92 Clear
Base, (all mixed w/M37 catalyst) |
|
| Technical
Data |
Tintable
White |
| Generic
Type |
Polyamide
Epoxy |
| Pigment
Type |
Titanium
Dioxide
and Select Inerts |
| Volume
Solids |
60%
Mixed |
| Spread
Rate per Gal. |
245
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
6.6
mils
4.0 mils |
Dry
Time
- To Touch
- Recoat |
2
hours
16 hours |
| Dry
Heat Resistance |
300°
F |
| Viscosity
(mixed) |
90
± 5 KU |
| Flash
Point (Seta) |
82°
F |
| 60°
Specular Gloss |
80-90% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
1:1
by volume |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
8
hours |
|
| |
|
| Polyamide
Epoxy Clear Sealer/Finish CM36-00/M37 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two component clear polyamide epoxy performs
dual functions.
First, reduced 1:1
with M95 Epoxy Reducer use as a deep penetrating
sealer on concrete and wood under high performance
top coats.
Second, as a clear
epoxy coating for floors and walls that provides
good chemical and abrasion resistance.
Recommended
Uses
Colors: M36-00
Clear Finish (Mixed with M37-84 Catalyst)
Tint Bases: None
(see M36 for colors)
|
|
| Technical
Data |
Clear |
| Generic
Type |
Polyamide
Epoxy |
| Pigment
Type |
Clear |
| Volume
Solids |
33%
Mixed |
| Spread
Rate per Gal. |
270
Sq.Ft.
(430 Sq.Ft.) |
Film
Thickness
- Wet
- Dry |
6.0
(3.7) mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
11/2
hours
4 hours |
| Dry
Heat Resistance |
200°
F |
| Viscosity
(mixed) |
70
± 5 KU |
| Flash
Point (Seta) |
81°
F
(84° F) |
| 60°
Specular Gloss |
85-95% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
1:1
by volume |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
8
hours |
|
| |
|
| Acrylic
Epoxy Gloss Coating M43/M44 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two component epoxy offers unique features
such as low fire hazard and application over
slightly damp surfaces. It has good color and
gloss retention for use on exterior or interior
surfaces, offers greatly improved chemical and
abrasion resistance plus extended pot life.
Recommended
Uses
Colors: Benjamin
Moore bases
|
|
| Technical
Data |
|
| Generic
Type |
Acrylic
Epoxy |
| Pigment
Type |
|
| Volume
Solids |
36%
Mixed |
| Spread
Rate per Gal. |
380
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
4.2
mils
1.5 mils |
Dry
Time
- To Touch
- Recoat |
2
hour
12 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity
(mixed) |
75
± 5 KU |
| Flash
Point (Seta) |
None
at 200° F |
| 60°
Specular Gloss |
60-70% |
| Clean
Up With |
Clean
Water |
| Mixing
Ratio |
4:1 |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
8
hours |
|
| |
|
| Acrylic
Epoxy Gloss Coating Clear M43-00/M44 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two component epoxy offers an unusual amount
of unique features such as low fire hazard and
application over slightly damp surfaces. It has
good gloss retention for use on exterior or
interior surfaces, offers greatly improved
chemical and abrasion resistance plus extended pot
life.
Recommended
Uses
Colors: M43-00
Clear Finish (Mixed with M44-84 Catalyst)
|
|
| Technical
Data |
Clear |
| Generic
Type |
Acrylic
Epoxy |
| Pigment
Type |
Clear |
| Volume
Solids |
32%
Mixed |
| Spread
Rate per Gal. |
340
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
4.7
mils
1.5 mils |
Dry
Time
- To Touch
- Recoat |
1
hour
12 hours |
| Dry
Heat Resistance |
160°
F |
| Viscosity
(mixed) |
75
± 5 KU |
| Flash
Point (Seta) |
None
at 200° F |
| 60°
Specular Gloss |
60-70% |
| Clean
Up With |
Clean
Water |
| Mixing
Ratio |
4:1 |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
8
hours |
|
| |
|
| Epoxy
Mastic Coating M45/46 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two component high build epoxy is
self-priming and has exceptional adhesion
even over tightly adhering rust. It also has
good flexibility and impact resistance, plus good
wetting properties, almost eliminating
undercutting at damaged areas. The high
solids provide exceptional coverage and the low
solvent reduces pinholes and lifting of
conventional coatings. May be used as a high
build primer, an intermediate coat or single coat
on interior applications. Minimum two coats
for exterior applications. For immersion use
in fresh or salt water.
Recommended
Uses
Tint Bases: M45-90
Tintable white, M45-91 deep base, M45-92 clear
base
|
|
| Technical
Data |
Tintable
White |
| Generic
Type |
Amide
Amine Epoxy |
| Pigment
Type |
TiO2
and Select Inerts |
| Volume
Solids |
78% |
| Spread
Rate per Gal. |
315
sq. feet |
Film
Thickness
- Wet
- Dry |
5.1
mils
4.0 mils |
Dry
Time
- To Touch
- Recoat |
4
hours
8 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
90+/-5
KU |
| Flash
Point (Seta) |
82°
F |
| 60°
Specular Gloss |
31% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
1:1 |
| Induction
Time |
30
minutes |
| Pot
Life @ 70° F |
6
hours |
|
| |
|
| Low
Cure Epoxy Mastic Coating M45L/46 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two component high build epoxy is
self-priming and has exceptional adhesion
even over tightly adhering rust. It also has
good flexibility and impact resistance, plus good
wetting properties, almost eliminating
undercutting at damaged areas. The high
solids provide exceptional coverage and the low
solvent reduces pinholes and lifting of
conventional coatings. May be used as a high
build primer, an intermediate coat or single coat
on interior applications. Minimum two coats
for exterior applications. For immersion use
in fresh or salt water.
Recommended
Uses
Tint Bases: M45L-90
Tintable white, M45L-91 deep base |
|
| Technical
Data |
Tintable
White |
| Generic
Type |
Modified
Amine
Epoxy |
| Pigment
Type |
TiO2
and Select Inerts |
| Volume
Solids |
76% |
| Spread
Rate per Gal. |
300
sq. feet |
Film
Thickness
- Wet
- Dry |
5.3
mils
4.0 mils |
Dry
Time
- To Touch
- Recoat |
2
hours
3.5 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
100+/-5
KU |
| Flash
Point (Seta) |
82°
F |
| 60°
Specular Gloss |
40% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
1:1 |
| Induction
Time |
30
minutes |
| Pot
Life @ 70° F |
2.5
hours |
|
| |
|
| Coal
Tar Epoxy M47/48 |
| MSDS |
Technical
Data Sheet |
Product
Information
This two component polyamide cured coal tar epoxy
is a 4 to 1 mixture with good pot life. Offers
very good splash and spill resistance to most
acids, alkalis, and mild solvents. Forms good
non-conductive insulating film for dissimilar
metals. Provides very good adhesion, flexibility,
and high film build on steel or concrete interior
or exterior areas. Steel surfaces for immersion
service should have near white metal blasting.
Recommended Uses
Interior or exterior concrete, metal surfaces,
ballast tanks, clarifiers, digesters, cooling
towers, offshore rigs, marine piping, spillways,
bar screens and retainer gates, waste treatment
plants, power plants, pulp and paper mills,
fertilizer plants, foundries and refineries
Not for potable
water service, not for immersion in strong acids
and strong solvents, blushing occurs during high
humidity and low temperature, limited low
temperature cure.
Colors: Black
|
|
| Technical
Data |
Black |
| Generic
Type |
Polyamide
Epoxy |
| Pigment
Type |
Coal
Tar |
| Volume
Solids |
68%
Mixed |
| Spread
Rate per Gal. |
135
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
11.8
mils
8.0 mils |
Dry
Time
- To Touch
- Recoat |
6
hours
8 hours |
| Dry
Heat Resistance |
200°
F |
| Viscosity
(mixed) |
110
± 10KU |
| Flash
Point (Seta) |
75°
F |
| 60°
Specular Gloss |
82% |
| Clean
Up With |
M95 |
| Mixing
Ratio |
4:1 |
| Induction
Time |
30
Min. |
| Pot
Life @ 70° F |
6-8
hours |
|
| |
|
| Anti-Slip
Aggregate M67 |
| MSDS |
Technical
Data Sheet |
Product
Information
This specially formulated anti-slip aggregate is
designed to elevate the foot or wheel on a damp or
wet surface, permitting the water to escape
instead of causing the foot or wheel to
hydroplane. Composed of Aluminosilicate, which is
very hard, and angular and blocky in shape, this
aggregate provides long term durability and
excellent slip resistant features. its clear color
also has minimal impact on the coating color due
to color differences. It is lightweight with a
specific gravity of 2.5 to 2.6, and offers
elasticity to yield under impact pressure. It
provides good chemical resistance, is free of
silica, spark resistant, and offers high
reflectivity, which improves light intensity. |
|
|
| |
|
| Moisture
Tolerant Epoxy Sealer/Finish M68/69 |
| MSDS |
Technical
Data Sheet |
|
Product
Information
This sealer/finish performs two roles: as a
penetrating sealer and as a high performance
finish coat. This product is formulated to
tolerate some moisture in the substrate, such as
areas that are slow in drying. This product
when used as a finish coat will protect wood or
concrete surfaces against water, oil, greasy
soils, salts, and many chemicals. If this
product | | | |
