| |
|
Rapid
Dry Gloss Enamel CM20
|
|
MSDS |
Technical
Data Sheet (pdf) |
Product
Information
This rapid dry gloss enamel is formulated for
interior or exterior use on surfaces requiring a
coating that dries to the touch in 15 minutes.
Available in 16 standard colors and unlimited
custom tinted colors. This product permits
equipment to be coated while it is being repaired
eliminating additional down time to allow paint to
dry. For additional gloss, chemical and abrasion
resistance add 1 pint of M76-85 Gloss &
Hardness Enhancer per gallon. This mixture has a
useable pot life of 3 hours at 70º F and 50%
humidity. Reference Product Data Sheet M73 M7603.
Recommended
Uses
Equipment, structural steel, metal doors and
cabinets, walls and dadoes, open bar joists,
machinery, catwalks, railings, piping,, tank,
drums
- Not for soft
substrates such as wood
- Not for floors
- Solvents in this product may lift previously
applied coatings
- Recoat within 3 hours or wait 36 hours
Colors: Tintable
White, Clear and colors
|
|
| Technical
Data |
White |
| Generic
Type |
Modified
Alkyd |
| Pigment
Type |
Titanium
Dioxide |
| Volume
Solids |
37%
(49%) |
| Spread
Rate per Gal. |
300
Sq.Ft.
(390 Sq. Ft.) |
Film
Thickness
- Wet
- Dry |
5.4
(4.1) mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
15
Minutes
see caution |
| Dry
Heat Resistance |
200°
F |
| Viscosity |
80
(65)± 5 KU |
| Flash
Point (Seta) |
74°
F |
| 60°Specular
Gloss |
85% |
| Clean
Up With |
M94 |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70°F |
N/A |
|
| |
|
| Urethane
Alkyd Gloss Enamel M22 / CM22 |
| MSDS |
Technical
Data Sheet (pdf) |
Product
Information
This urethane alkyd is superior to conventional
alkyds when applied to surfaces that are
intermittently exposed to light chemical
environments. Provides better color and gloss
retention than epoxy esters on exterior exposures.
Provides good abrasion resistance on high traffic
floor areas. Designed for interior or exterior
application on metal, wood or concrete surfaces.
Easily applied by brush, roller or various spray
methods.
Recommended
Uses
Metal, wood, concrete, equipment, machinery,
floors, marine exposure (above water), railings,
catwalks, piping, doors, cabinets, storage tanks,
metal buildings, conveyers, fences, general
maintenance
Colors: Tintable
White, Deep Base, Clear Base, Moor-O-Matic bases
|
|
| Technical
Data |
White |
| Generic
Type |
Urethane
Alkyd |
| Pigment
Type |
Titanium
Dioxide |
| Volume
Solids |
42%
(47%) |
| Spread
Rate per Gal. |
340
Sq.Ft.
(370 Sq.Ft). |
Film
Thickness
- Wet
- Dry |
4.8
mils (4.3)
2.0 mils |
Dry
Time
- To Touch
- Recoat |
2
Hours
8 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
75
± 5 KU |
| Flash
Point (Seta) |
103°
F |
| 60°Specular
Gloss |
85% |
| Clean
Up With |
Mineral
Spirits |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70°F |
N/A |
|
| |
|
|
Gloss
and Hardener Enhancer M76 |
| MSDS |
|
Product
Information
This product is designed to be added to M20/CM20
Rapid Dry Gloss Enamel. Its function is to improve
the color and gloss retention plus increase the
chemical and abrasion resistance.
Recommended
Uses
Equipment Machinery Storage containers Buildings
Rolling stock Ground equipment
Towers, Lockers, Construction equipment Highway
and mining equipment
|
|
|
| |
|
| D.T.M.
(Direct to Metal) Alkyd Semi-Gloss M24,
CM24 |
| MSDS |
Technical
Data Sheet (pdf) |
Product
Information
This product is designed to perform a dual purpose
as a direct to metal primer and as a tough durable
finish coat. Both coats of this product provide
rust inhibition for superior corrosion control.
This semi-gloss finish hides most surface
imperfections while providing good color and sheen
retention on both interior or exterior surfaces.
Uncoated ferrous metal must receive a minimum of
two coats for adequate corrosion control.
Recommended
Uses
Protects metal, wood or concrete on interior or
exterior surfaces. Performs well on machinery,
storage tanks, equipment, catwalks, railings,
metal pan ceilings, open bar joists, roofing
equipment, metal doors & lockers, piping,
metal buildings, fences, conveyers, or for general
maintenance painting.
Colors: M24-90
Tintable White, M24-91 Deep Base, M24-92 Clear
Base |
|
| Technical
Data |
Tintable
White |
| Generic
Type |
Modified
Alkyd |
| Pigment
Type |
Titanium
Dioxide |
| Volume
Solids |
44%
(47%) |
| Spread
Rate per Gal. |
355
Sq.Ft.
(380 Sq. Ft.) |
Film
Thickness
- Wet
- Dry |
4.5
(4.2) mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
1
Hour
8 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
83
± 5 KU |
| Flash
Point (Seta) |
103°
F |
| 60°Specular
Gloss |
50% |
| Clean
Up With |
Mineral
Spirits |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70°F |
N/A |
|
| |
|
| Epoxy
Ester Gloss Enamel M25, CM25 |
| MSDS |
Technical
Data Sheet (pdf) |
Product
Information
This high gloss single component epoxy ester
enamel is designed to provide increased resistance
to animal fats, oils, diluted acids and alkalis.
It provides increased abrasion resistance and
resists repeated cleanings when used on floors.
Performs well when used for general maintenance
painting for protecting surfaces in water and
waste treatment plants, food processing plants,
bottling plants, dairies, and other areas exposed
to high moisture or humidity.
Recommended
Uses
Performs well on machinery, storage tanks,
equipment, forklifts, and high traffic floor
areas, catwalks, railings and steps, metal doors
and lockers, piping, conveyors, and material
handling equipment. For general maintenance
painting of surfaces exposed to high moisture or
mild alkalis.
Colors: M25-73
Platinum Gray, M25-74 Light Gray
Tint Bases: M25-91
Deep Base, M25-92 Clear Base, M24-92 Clear Base |
|
| Technical
Data |
|
| Generic
Type |
Epoxy
Ester |
| Pigment
Type |
Titanium
Dioxide |
| Volume
Solids |
43%
(47%) |
| Spread
Rate per Gal. |
350
Sq.Ft.
(380 Sq. Ft.) |
Film
Thickness
- Wet
- Dry |
4.6
(4.2) mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
4
hours
10 hours |
| Dry
Heat Resistance |
250°
F |
| Viscosity |
75
± 5 KU |
| Flash
Point (Seta) |
105°
F |
| 60°Specular
Gloss |
85% |
| Clean
Up With |
Mineral
Spirits |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70°F |
N/A |
|
| |
|
| D.T.M.
Alkyd Gloss Enamel M26 |
| MSDS |
Technical
Data Sheet (pdf) |
Product
Information
This product is designed to perform a dual purpose
as a direct-to-metal primer and as a tough,
durable finish coat. Both coats of this product
provide rust inhibition for superior corrosion
control. Uncoated ferrous metal must receive a
minimum of two coats for adequate corrosion
control. This product is also formulated with
couplers which will absorb surface moisture and
carry it out through the surface of the coating as
evaporation takes place. Remove all excess
moisture by wiping with clean dry rags just before
painting.
Recommended
Uses
Recommended For: • Coating Damp Metal Surfaces
• Water or Waste Treatment Plants • Nursing
and Personal Care Facilities • Equipment •
Storage Tanks • Interior or Exterior Surfaces
• Bottling Plants • Washing Areas •
Hospitals • Machinery • Ceilings and Walls
Limitations
Not for immersion service • Application over
damp surfaces must be by brush only. • Not to be
applied over wet surfaces • Not for floor
applications
Colors: M26-90
Tintable White Only
|
|
| Technical
Data |
Tintable
White |
| Generic
Type |
Modified
Alkyd |
| Pigment
Type |
TiO2
& Zinc Phosphate |
| Volume
Solids |
47% |
| Spread
Rate per Gal. |
375
Sq.Ft. |
Film
Thickness
- Wet
- Dry |
4.3
mils
2.0 mils |
Dry
Time
- To Touch
- Recoat |
2
Hours
8 hours |
| Dry
Heat Resistance |
300°
F |
| Viscosity |
75
± 5 KU |
| Flash
Point (Seta) |
115°
F |
| 60°Specular
Gloss |
85% |
| Clean
Up With |
Mineral
Spirits |
| Mixing
Ratio |
N/A |
| Induction
Time |
N/A |
| Pot
Life @ 70° F |
N/A |
|
|
|
|
